Pathway eDIN Analog-to-DMX converts analog voltages or dry contact input to DMX512.

1006 Analog to DMX

The eDIN #1006 converts 24 analog 0-10VDC sources or 24 dry contact closures into a DMX512 signal.   A built-in DMX merger combines signal output with other in-line #1006 interfaces,  lighting consoles or controllers.  Also may be used as a simple snapshot playback device, holding up to 24 ‘looks’.

  • DMX512 start address and operating mode may be set from front panel interface or remotely using E1.20 RDM
  • Indicator LEDs for power, processor, DMX input status and contact closure operation
  • Convert 0-10VDC input to DMX512 output levels
  • Alternate contact closure mode, for off/full DMX control
  • Recall mode allows capture and playback of up to 24 discrete, full universe ‘looks’
  • LED indicator for CCI mode
  • Built-in merger allows in-line operation with other DMX sources in either recall or input modes
  • One DMX512-A/RDM data input connection
  • One passive DMX512-A data through connection
  • Data and power easily daisy-chained between modules
  • Termination switch
  • Independent test function, in both analog and contact closure modes
  • Firmware field-upgradable using RDM (requires Pathway Pathport gateway and RDM utility program)
  • Highest Takes Precedence (HTP)
  • Analog Takes Precedence
  • DMX Takes Precedence
  • Contact Closure Input
  • Preset Recall
  • DMX Takes Precedence over Preset Recall
  • 1500V opto-isolation between input and output ports
  • 250V fault protection on input and output ports
  • Input operating voltage: 9-30 VDC
  • 6W power consumption
  • Operating conditions: -10°-50°C; 10-90% relative humidity, non-condensing
  • ANSI E1.11 DMX512-A(2008)/USITT DMX512(1990)
  • ANSI E1.20 RDM(2010) - Remote Device Management
  • ANSI E1.3 0-10V Analog Control
  • RoHS 2002/95/EC
  • Class 2 Low Voltage
  • 0.70 lbs (0.316 kg)
  • 3.6”W x 6.25”L x 1.5”H  (91mm x 160mm x 38mm)

Model

Description

1006

eDIN Analog-to-DMX, 24 Channel

Accessories

1001-030-24-DIN

30 Watt, 24VDC Power Supply, DIN-Mountable

1001-100-24-DIN

100 Watt, 24VDC Power Supply, DIN-Mountable

1103

eDIN Rack Mount Panel,
2RU high, two 16.5" DIN Rail

1105

eDIN System Enclosure, 10" x 13" x 4.5"
c/w One 9" Vertical DIN Rail

1106

eDIN System Enclosure, 10" x 23" x 4.5"
c/w One 19" Vertical DIN Rail

1107

eDIN System Enclosure, 10" x 23" x 4.5"
c/w Three 9" Horizontal DIN Rail

1108

eDIN System Enclosure, 10" x 13" x 4.5"
c/w Two 9" Horizontal DIN Rail

1109

Expanded eDIN System Enclosure 18.5" x 31.5" x 6.5"
c/w Three 24"Vertical DIN Rail,
One 18” DIN Rail in Class 1 section,
two 3-gang knockouts in removable door

4000

  eDIN Enclosure Assembly Service

Resources:

Data Sheet

Manual

Drawings:

.DWG    .PDF

Specification